View Full Version : small knurled, threaded knobs needed
dkbgs 01-03-2006, 04:23 PM 6061-T6 rod
.620" od with medium hatched knurling. Parts are .625" long, drilled through 3/32" and internally threaded 4-40 at one end, drilled .125" dia x .3" deep at other. Threaded end of knob has a 2.5 degree point/camfer, other end has a dome radius of 1 1/2" approximately. Concentricity must be within .002, length and OD within .005"
Knurling must look good!
Vibratory finish and degreased
200 - 1000 parts depending on price
Local to Portland, OR is encouraged!
Thanks
email me: david(at)kingbass(dot)com
ironman 01-06-2006, 06:43 PM 6061-T6 rod
.620" od with medium hatched knurling. Parts are .625" long, drilled through 3/32" and internally threaded 4-40 at one end, drilled .125" dia x .3" deep at other. Threaded end of knob has a 2.5 degree point/camfer, other end has a dome radius of 1 1/2" approximately. Concentricity must be within .002, length and OD within .005"
Knurling must look good!
Vibratory finish and degreased
200 - 1000 parts depending on price
Local to Portland, OR is encouraged!
Thanks
email me: david(at)kingbass(dot)com I can do it on the screw mach. for $ 1.10 ea plus shipping. Eric Laycock, Laycock Tool.:)
ironman 01-06-2006, 06:44 PM I fogot to tell you I'm in Northern AZ. (928) 207 1990
easyvalk 02-10-2006, 09:12 PM QTY. 200 = $1.75 each plus shipping
QTY. 1000 = $0.95 each plus shipping
Need drawing or can make per picture with demensions as specified
Quote material and labor to machine complete per drawing.
Everett Pendergrass
T&E Precision Tooling
865-435-1509 phone
865-435-1576 fax
kmcmachineworks 03-02-2006, 01:51 AM I will do them for $.95 each plus shipping
will need also a time frame as to when you need them.
kmcmachineworks@hotmail.com
www.kmcmachineworks.netfirms.com
machineguy 03-02-2006, 09:29 PM Hi I can machine these for $1.20 ea qty 200 or $1.00 ea qty 1000 plus shipping.I would like a drawing and time frame for completion if awarded the bid.
Thanks
Cutting Edge Machine
Jeff3 03-16-2006, 09:59 AM 6061-T6 rod
.620" od with medium hatched knurling. Parts are .625" long, drilled through 3/32" and internally threaded 4-40 at one end, drilled .125" dia x .3" deep at other. Threaded end of knob has a 2.5 degree point/camfer, other end has a dome radius of 1 1/2" approximately. Concentricity must be within .002, length and OD within .005"
Knurling must look good!
Vibratory finish and degreased
200 - 1000 parts depending on price
Local to Portland, OR is encouraged!
Thanks
email me: david(at)kingbass(dot)com
I run a job close to this one.
200 + for $0.95 plus shipping
1000 + for $0.65 plus shipping
Jeff Thompson
Alpha Machining, Inc
904-276-6131
904-276-6132 Fax
marto74 05-12-2006, 02:05 PM 6061-T6 rod
.620" od with medium hatched knurling. Parts are .625" long, drilled through 3/32" and internally threaded 4-40 at one end, drilled .125" dia x .3" deep at other. Threaded end of knob has a 2.5 degree point/camfer, other end has a dome radius of 1 1/2" approximately. Concentricity must be within .002, length and OD within .005"
Knurling must look good!
Vibratory finish and degreased
200 - 1000 parts depending on price
Local to Portland, OR is encouraged!
Thanks
email me: david(at)kingbass(dot)com
We can do this parts for you if it's not a problem that we are from Europe
Regards: Martin
Metalmog 08-08-2006, 07:01 PM 6061-T6 rod
.620" od with medium hatched knurling. Parts are .625" long, drilled through 3/32" and internally threaded 4-40 at one end, drilled .125" dia x .3" deep at other. Threaded end of knob has a 2.5 degree point/camfer, other end has a dome radius of 1 1/2" approximately. Concentricity must be within .002, length and OD within .005"
Knurling must look good!
Vibratory finish and degreased
200 - 1000 parts depending on price
Local to Portland, OR is encouraged!
Thanks
email me: david(at)kingbass(dot)com
Make similar parts & fasteners, located Vancouver, BC. Mainly out of 303 stainless and brass.
Material: 6061-T6 (included)
Finishing: Vibratory. (not really required if as shown in pictures, parts come off machine cleanly unless high shine required, such as in mirror polished)
Surface treatment: Non, other than mineral degreasing (but not clean enough for electroplating or anodizing). Recommend a light coating of preservative to prevent oxidation during shipping and storage.
Accuracy: much better than required.
Need Thread class of fit and delivery time?
Qty - Price
200 - US$1.00
1000 - US$0.62
5000 - US$0.52
Delivery 8 weeks from receipt of order unless otherwise required. Valid for 30 days.
versa1 08-13-2006, 10:55 AM I would be interested in building these parts for you, have you awarded yet?
Contact me: versautility@yahoo.com
6061-T6 rod
.620" od with medium hatched knurling. Parts are .625" long, drilled through 3/32" and internally threaded 4-40 at one end, drilled .125" dia x .3" deep at other. Threaded end of knob has a 2.5 degree point/camfer, other end has a dome radius of 1 1/2" approximately. Concentricity must be within .002, length and OD within .005"
Knurling must look good!
Vibratory finish and degreased
200 - 1000 parts depending on price
Local to Portland, OR is encouraged!
Thanks
email me: david(at)kingbass(dot)com
|