Search results

  1. M

    Machining Work Needed

    Are you sure you need +/-.001" on all dimensions?
  2. M

    Request For Quote- Brass Flywheel, Quote For Qty 50

    +/-.0001" hole location tolerance is a bit of wishful thinking. I get that you want this for balance, but this accuracy, if actually measured and verified, would make this part far more expensive than if it was simply dynamically balanced after machining. Regards. Mike
  3. M

    Small Delrin Parts - Qty 25

    68F/20C, but whatever ... that tolerance is probably not serious, given that the drawing appears to call out the thread length to 3 decimals, hence +/-.001", which IMO is unmeasurable. Regards.
  4. M

    Is this thing on?

    Just wondering if this site is operational. No new posts in the past week or so? Regards. Mike
  5. M

    Request For Quote- 6061-T6 Bucket

    I'm not going to quote, but would be interested to know how you guys plan on reaching down into that bore to work the bottom contour. Gigantic ball endmill? Big boring bar on the lathe?
  6. M

    Request For Quote- 1-1/4" hex shaft 4140, turned end with key ways, drilled, tapped

    Try editing your original post and attach your drawings. It seems that until a thread has been created, files cannot be attached. Regards. Mike
  7. M

    Prototype Needed Small Aluminum Prototype Needed - 1 Part

    Your drawing is a little janked up. You've got a 1/2" x 13 OD thread, with a 5/8" x 18 ID thread. Not possible :p You probably meant 1/2" x 13 ID thread, with a 5/8" x 18 OD thread. What sort of thread terminations do you want? Threads can terminate into a thread relief groove, or just...
  8. M

    Need RFQ for some of these Collars

    Whoever bids these, you're going to have to grind the critical dimensions after heat treat. Regards. Mike
  9. M

    Request For Quote- Quote for 30 Pieces

    OP, your PM box is full :-). Regards. Mike Schetterer Finegrain Metalworks www.finegrainmetal.com
  10. M

    Request For Quote- ONE OFF, 316 STAINLESS inspection type part needed.

    Your private message queue is full. Do you have an alternate contact? Regards Mike
  11. M

    Request For Quote- Looking for a quote for 1,000 of these corner weld nuts at a time

    Will these parts get welded? They are called "Weld Nut" after all. Anyway, 303 is not recommended for welding. Regards. Mike
  12. M

    Quote Request

    What condition 6150? Annealed or heat treated? 6150 is uncommon in small round bar. How about 4140 or 4340 instead? Regards. Mike
  13. M

    Request For Quote- Screw Prototype

    WEDM is the only way to accomplish what you describe. Regards. Mike
  14. M

    Request For Quote- RFQ for 6061 Turning Job 100 pieces

    Sent you a PM. Regards. Mike
  15. M

    Small Job Quote Needed Aluminium, Small Run Parts

    Hi Randy, Sent you a PM. I'm not able to view your attachments, tried a couple different browsers. Regards. Mike Schetterer Finegrain Metalworks mike@finegrainmetal.com
  16. M

    Request For Quote- Lathe Work RFQ

    Material? Tolerances? Regards. Mike
  17. M

    Small Job Quote Needed Easy Job, Stainless Rods

    McMaster Carr carries -.0002" 304. Regards. Mike
  18. M

    Request For Quote- Aluminum 100 pcs to start

    I can't open your attachment. Can you PLZ reattach it, or send it to me at finegrainmetal <at> Hotmail <dot> com? Thanks, and regards. Mike
  19. M

    Turned Cones RFQ

    Sent you a PM., I can send an e-mail as well, just need an e-mail address. Regards. Mike
Top