Request For Quote- 2 Small Very Simple Parts Needed ** Now Closed

Status
Not open for further replies.

amasters

Thermo_man
I am looking for a quote on the following VERY simple parts.

Both parts are to be machined from Copper 101, 110, or 122 [NO BRASS or BRONZE!]

I have suggested a source for the material on each drawing, but if you have a suitable and more economical source (as long as it is the same material) then use it. Please provide proof that the material is as requested such as a receipt/packing slip/certification that indicates the alloy of copper supplied.

Please quote machined part including material cost. I will supply a UPS account for collect shipping.

Parts will be shipped to Bishopville, MD 21813

Please quote: 100, 250, 500, and 1000 pieces of each and lead time.

Let me know if you have any questions or concerns.

3D Part files available in SolidWorks or others as requested.

I expect to close this request in a week to 10 days.


Thanks for looking,

Andy

amasters(at)customthermoelectric(dot)com
 

Attachments

  • WBP-0.10-0.16-CU_REV-B.PDF
    103.5 KB · Views: 119
  • WBT-0.65-0.16-CU_REV-B.PDF
    82.7 KB · Views: 81

Jim D

New Member
I am looking for a quote on the following VERY simple parts.

Both parts are to be machined from Copper 101, 110, or 122 [NO BRASS or BRONZE!]

I have suggested a source for the material on each drawing, but if you have a suitable and more economical source (as long as it is the same material) then use it. Please provide proof that the material is as requested such as a receipt/packing slip/certification that indicates the alloy of copper supplied.

Please quote machined part including material cost. I will supply a UPS account for collect shipping.

Parts will be shipped to Bishopville, MD 21813

Please quote: 100, 250, 500, and 1000 pieces of each and lead time.

Let me know if you have any questions or concerns.

3D Part files available in SolidWorks or others as requested.

I expect to close this request in a week to 10 days.


Thanks for looking,

Andy

amasters(at)customthermoelectric(dot)com

I was curious if there are any requirements for finish on the ends of the Plug.
 

Dantrivits

New Member
I am looking for a quote on the following VERY simple parts.

Both parts are to be machined from Copper 101, 110, or 122 [NO BRASS or BRONZE!]

I have suggested a source for the material on each drawing, but if you have a suitable and more economical source (as long as it is the same material) then use it. Please provide proof that the material is as requested such as a receipt/packing slip/certification that indicates the alloy of copper supplied.

Please quote machined part including material cost. I will supply a UPS account for collect shipping.

Parts will be shipped to Bishopville, MD 21813

Please quote: 100, 250, 500, and 1000 pieces of each and lead time.

Let me know if you have any questions or concerns.

3D Part files available in SolidWorks or others as requested.

I expect to close this request in a week to 10 days.


Thanks for looking,

Andy

amasters(at)customthermoelectric(dot)com

Email Sent
 

amasters

Thermo_man
I'm closing this on midnight EST (New York time zone) Monday Aug. 21st. Please get your quotes in if you want to be considered.

Thank you to those that have already sent in quotes.

Andy
 

amasters

Thermo_man
This request is now closed. Thank you to all who quoted.

Just FYI, here are the statistics on the quotes I received. Vendor names removed.
9 quotes received.

ALL vendors were based in the USA.

See attached imageQuote summary for copper tubes and plugs 8-2017.JPG
 

Sukh

New Member
Appreciate you taking the time out to create the table. Nice to see how different companies vary.
 
Status
Not open for further replies.
Top